Schedule A Service Call

 

 

Almost everyone has his or her own conception involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough project. If the old tub is readily obtainable, the job can move quickly; if you have to open a wall surface to eliminate the old tub and also position the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the new one. Make certain you have certified yourself for the job and also are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one before you begin. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to change the plan of your previous water pipes.
Your tools and also material checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in location between the tap and the sink. Protect the faucet in position with the maker supplied backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap finishes initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Setting up the Tub

Using the two wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level reviews level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its final setting.

 

 

Preparing for the Installment

First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final setting.

 

 

Tiling Around the Tub

In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with moisture and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can break relatively early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about Tools You Need to Install a New Bathtub ? Make feedback down the page. We'd be interested to know your ideas about this write up. Hoping that you come back again in the future. I beg you set aside a second to distribute this post if you liked it. Thank-you for your time invested reading it.

Visit Url